Effect of Pitch Thread Combination of Dental Implant on Fatigue Safety and Life Performance
DOI:
https://doi.org/10.47701/icohetech.v1i1.1093Keywords:
dental implant, thread pitch, fatigue safety factor, life performance, ANSYS/WorkbenchAbstract
During the implant procedure, one factor determining the surgery's success is the dental implant's stability. The stability index includes fatigue safety and life performance. A dental implant's thread pitch has been regarded as the essential factor for fatigue safety in many studies. However, the effect of the mixed thread pitch on fatigue safety and life performance are rarely investigated. Therefore, this study examines the impact of thread pitch on implants on the fatigue safety factor and dental implants' life. Four types of implants were studied: (0.5mm Pitch, 0.8mm Pitch, Combination Pitch (0.8mm with upper 0.5mm and 0.8mm with lower 0.5 mm). The material of a dental implant used in this study is Ti6al4v. According to ISO standard 14801, the fatigue safety factor is presented and compared using ANSYS/Workbench software. The results show that the combination pitch (0.8mm with upper Pitch 0.5 mm) has the highest life and safety factors.
References
P. Trisi, M. Berardini, A. Falco, and M. Podaliri Vulpiani, "Validation of value of actual micromotion as a direct measure of implant micromobility after healing (secondary implant stability). An in vivo histologic and biomechanical study," Clin. Oral Impl. Res., vol. 27, no. 11, pp. 1423–1430, Nov. 2016, doi: 10.1111/clr.12756.
F. Javed, H. B. Ahmed, R. Crespi, and G. E. Romanos, "Role of primary stability for successful osseointegration of dental implants: Factors of influence and evaluation," Interventional Medicine and Applied Science, vol. 5, no. 4, pp. 162–167, Dec. 2013, doi: 10.1556/IMAS.5.2013.4.3.
K. Shemtov-Yona and D. Rittel, "Fatigue of Dental Implants: Facts and Fallacies," Dentistry Journal, vol. 4, no. 2, p. 16, May 2016, doi: 10.3390/dj4020016.
R. Brånemark, P. I. Brånemark, B. Rydevik, and R. R. Myers, "Osseointegration in skeletal reconstruction and rehabilitation: A review," Journal of Rehabilitation Research and Development, vol. 38, no. 2, 2001.
K. E. Tanner, "Titanium in Medicine," Proc Inst Mech Eng H, vol. 216, no. 3, pp. 215–215, Mar. 2002, doi: 10.1243/0954411021536432.
Y.-C. Cheng, C.-P. Jiang, and D.-H. Lin, "Finite element based optimization design for a one-piece zirconia ceramic dental implant under dynamic loading and fatigue life validation," Struct Multidisc Optim, vol. 59, no. 3, pp. 835–849, Mar. 2019, doi: 10.1007/s00158-018-2104-2.
C. Imakita, M. Shiota, Y. Yamaguchi, S. Kasugai, and N. Wakabayashi, "Failure Analysis of an Abutment Fracture on Single Implant Restoration," Implant Dentistry, vol. 22, no. 4, pp. 326–331, Aug. 2013, doi: 10.1097/ID.0b013e31829a16fd.
N.-H. Choi, H.-I. Yoon, T.-H. Kim, and E.-J. Park, "Improvement in Fatigue Behavior of Dental Implant Fixtures by Changing Internal Connection Design: An In Vitro Pilot Study," Materials, vol. 12, no. 19, p. 3264, Oct. 2019, doi: 10.3390/ma12193264.
ISO14801, "Fatigue Test for Endosseous Dental Implants." International Organization for Standardization, 2013.
M. Armentia, M. Abasolo, I. Coria, and J. Albizuri, "Fatigue Design of Dental Implant Assemblies: A Nominal Stress Approach," Metals, vol. 10, no. 6, p. 744, Jun. 2020, doi: 10.3390/met10060744.
M. Vivan Cardoso et al., "Dental Implant Macro-Design Features Can Impact the Dynamics of Osseointegration: Implant Design and Osseointegration," Clinical Implant Dentistry and Related Research, vol. 17, no. 4, pp. 639–645, Aug. 2015, doi: 10.1111/cid.12178.
J. P. Geng, W. Xu, K. B. C. Tan, and G. R. Liu, "Finite Element Analysis of an Osseointegrated Stepped Screw Dental Implant," Journal of Oral Implantology, vol. 30, no. 4, pp. 223–233, Aug. 2004, doi: 10.1563/0654.1.
J. P. Geng, Q. S. Ma, W. Xu, K. B. C. Tan, and G. R. Liu, "Finite element analysis of four thread-form configurations in a stepped screw implant," J Oral Rehabil, vol. 31, no. 3, pp. 233–239, Mar. 2004, doi: 10.1046/j.0305-182X.2003.01213.x.
H. Abuhussein, G. Pagni, A. Rebaudi, and H.-L. Wang, "The effect of thread pattern upon implant osseointegration," Clinical Oral Implants Research, vol. 21, no. 2, pp. 129–136, Feb. 2010, doi: 10.1111/j.1600-0501.2009.01800.x.
Y. Duan, J. A. Gonzalez, P. A. Kulkarni, W. W. Nagy, and J. A. Griggs, "Fatigue lifetime prediction of a reduced-diameter dental implant system: Numerical and experimental study," Dental Materials, vol. 34, no. 9, pp. 1299–1309, Sep. 2018, doi: 10.1016/j.dental.2018.06.002.
P. Dhatrak, U. Shirsat, V. Deshmukh, and S. Sumanth, "Fatigue Life Prediction of Commercial Dental Implant Using Analytical Approach and Verification by FEA," in Proceedings of Fatigue, Durability and Fracture Mechanics, S. Seetharamu, K. B. S. Rao, and R. W. Khare, Eds. Singapore: Springer Singapore, 2018, pp. 203–212.
M. R. Niroomand and M. Arabbeiki, "Statistical analysis of implant and thread parameters effects on dental implant stability and bone resorption using central composite design method," Proc Inst Mech Eng H, vol. 233, no. 12, pp. 1299–1309, Dec. 2019, doi: 10.1177/0954411919881250.
G. Cervino et al., "Fem and Von Mises Analysis of OSSTEM ® Dental Implant Structural Components: Evaluation of Different Direction Dynamic Loads," TODENTJ, vol. 12, no. 1, pp. 219–229, Mar. 2018, doi: 10.2174/1874210601812010219.
M. Yalçın, B. Kaya, N. Laçin, and E. Arı, "Three-Dimensional Finite Element Analysis of the Effect of Endosteal Implants with Different Macro Designs on Stress Distribution in Different Bone Qualities," Int J Oral Maxillofac Implants, vol. 34, no. 3, pp. e43–e50, May 2019, doi: 10.11607/jomi.7058.
H. Oliveira et al., "Effect of Different Implant Designs on Strain and Stress Distribution under Non-Axial Loading: A Three-Dimensional Finite Element Analysis," IJERPH, vol. 17, no. 13, p. 4738, Jul. 2020, doi: 10.3390/ijerph17134738.
F. Bayata and C. Yildiz, "The Mechanical Behaviors of Various Dental Implant Materials under Fatigue," Advances in Materials Science and Engineering, vol. 2018, pp. 1–10, 2018, doi: 10.1155/2018/5047319.
M. Janeček et al., "The Very High Cycle Fatigue Behaviour of Ti- 6Al-4V Alloy," Acta Phys. Pol. A, vol. 128, no. 4, pp. 497–503, Oct.2015, doi: 10.12693/APhysPolA.128.497
F. Javed, H. B. Ahmed, R. Crespi, and G. E. Romanos, "Role of primary stability for successful osseointegration of dental implants: Factors of influence and evaluation," Interventional Medicine and Applied Science, vol. 5, no. 4, pp. 162–167, Dec. 2013, doi: 10.1556/IMAS.5.2013.4.3.
K. Shemtov-Yona and D. Rittel, "Fatigue of Dental Implants: Facts and Fallacies," Dentistry Journal, vol. 4, no. 2, p. 16, May 2016, doi: 10.3390/dj4020016.
R. Brånemark, P. I. Brånemark, B. Rydevik, and R. R. Myers, "Osseointegration in skeletal reconstruction and rehabilitation: A review," Journal of Rehabilitation Research and Development, vol. 38, no. 2, 2001.
K. E. Tanner, "Titanium in Medicine," Proc Inst Mech Eng H, vol. 216, no. 3, pp. 215–215, Mar. 2002, doi: 10.1243/0954411021536432.
Y.-C. Cheng, C.-P. Jiang, and D.-H. Lin, "Finite element based optimization design for a one-piece zirconia ceramic dental implant under dynamic loading and fatigue life validation," Struct Multidisc Optim, vol. 59, no. 3, pp. 835–849, Mar. 2019, doi: 10.1007/s00158-018-2104-2.
C. Imakita, M. Shiota, Y. Yamaguchi, S. Kasugai, and N. Wakabayashi, "Failure Analysis of an Abutment Fracture on Single Implant Restoration," Implant Dentistry, vol. 22, no. 4, pp. 326–331, Aug. 2013, doi: 10.1097/ID.0b013e31829a16fd.
N.-H. Choi, H.-I. Yoon, T.-H. Kim, and E.-J. Park, "Improvement in Fatigue Behavior of Dental Implant Fixtures by Changing Internal Connection Design: An In Vitro Pilot Study," Materials, vol. 12, no. 19, p. 3264, Oct. 2019, doi: 10.3390/ma12193264.
ISO14801, "Fatigue Test for Endosseous Dental Implants." International Organization for Standardization, 2013.
M. Armentia, M. Abasolo, I. Coria, and J. Albizuri, "Fatigue Design of Dental Implant Assemblies: A Nominal Stress Approach," Metals, vol. 10, no. 6, p. 744, Jun. 2020, doi: 10.3390/met10060744.
M. Vivan Cardoso et al., "Dental Implant Macro-Design Features Can Impact the Dynamics of Osseointegration: Implant Design and Osseointegration," Clinical Implant Dentistry and Related Research, vol. 17, no. 4, pp. 639–645, Aug. 2015, doi: 10.1111/cid.12178.
J. P. Geng, W. Xu, K. B. C. Tan, and G. R. Liu, "Finite Element Analysis of an Osseointegrated Stepped Screw Dental Implant," Journal of Oral Implantology, vol. 30, no. 4, pp. 223–233, Aug. 2004, doi: 10.1563/0654.1.
J. P. Geng, Q. S. Ma, W. Xu, K. B. C. Tan, and G. R. Liu, "Finite element analysis of four thread-form configurations in a stepped screw implant," J Oral Rehabil, vol. 31, no. 3, pp. 233–239, Mar. 2004, doi: 10.1046/j.0305-182X.2003.01213.x.
H. Abuhussein, G. Pagni, A. Rebaudi, and H.-L. Wang, "The effect of thread pattern upon implant osseointegration," Clinical Oral Implants Research, vol. 21, no. 2, pp. 129–136, Feb. 2010, doi: 10.1111/j.1600-0501.2009.01800.x.
Y. Duan, J. A. Gonzalez, P. A. Kulkarni, W. W. Nagy, and J. A. Griggs, "Fatigue lifetime prediction of a reduced-diameter dental implant system: Numerical and experimental study," Dental Materials, vol. 34, no. 9, pp. 1299–1309, Sep. 2018, doi: 10.1016/j.dental.2018.06.002.
P. Dhatrak, U. Shirsat, V. Deshmukh, and S. Sumanth, "Fatigue Life Prediction of Commercial Dental Implant Using Analytical Approach and Verification by FEA," in Proceedings of Fatigue, Durability and Fracture Mechanics, S. Seetharamu, K. B. S. Rao, and R. W. Khare, Eds. Singapore: Springer Singapore, 2018, pp. 203–212.
M. R. Niroomand and M. Arabbeiki, "Statistical analysis of implant and thread parameters effects on dental implant stability and bone resorption using central composite design method," Proc Inst Mech Eng H, vol. 233, no. 12, pp. 1299–1309, Dec. 2019, doi: 10.1177/0954411919881250.
G. Cervino et al., "Fem and Von Mises Analysis of OSSTEM ® Dental Implant Structural Components: Evaluation of Different Direction Dynamic Loads," TODENTJ, vol. 12, no. 1, pp. 219–229, Mar. 2018, doi: 10.2174/1874210601812010219.
M. Yalçın, B. Kaya, N. Laçin, and E. Arı, "Three-Dimensional Finite Element Analysis of the Effect of Endosteal Implants with Different Macro Designs on Stress Distribution in Different Bone Qualities," Int J Oral Maxillofac Implants, vol. 34, no. 3, pp. e43–e50, May 2019, doi: 10.11607/jomi.7058.
H. Oliveira et al., "Effect of Different Implant Designs on Strain and Stress Distribution under Non-Axial Loading: A Three-Dimensional Finite Element Analysis," IJERPH, vol. 17, no. 13, p. 4738, Jul. 2020, doi: 10.3390/ijerph17134738.
F. Bayata and C. Yildiz, "The Mechanical Behaviors of Various Dental Implant Materials under Fatigue," Advances in Materials Science and Engineering, vol. 2018, pp. 1–10, 2018, doi: 10.1155/2018/5047319.
M. Janeček et al., "The Very High Cycle Fatigue Behaviour of Ti- 6Al-4V Alloy," Acta Phys. Pol. A, vol. 128, no. 4, pp. 497–503, Oct.2015, doi: 10.12693/APhysPolA.128.497
Downloads
Published
2021-04-06
